Henny Penny Island Warmer Model HMI-103 Model HMI-105TECHNICAL MANUAL
Model HMI-103/1052-4. RADIANT HEATERS 1. Remove electrical power supplied to the unit. To avoid electrical shock or property damage, move
Model HMI-103/1052-6. AIR HEATERS 1. Remove electrical power supplied to the unit. To avoid electrical shock or property damage, move po
Model HMI-103/1052-7. POWER SWITCH (Continued) 4. Check across top and bottom terminals for continuity. With the switch in the ON position,
Model HMI-103/1052-9. HIGH LIMIT 1. Remove electrical power supplied to the unit. To avoid electrical shock or property damage, move pow
Model HMI-103/1052-10. FRONT GLASS REMOVAL 1. Using a fl at blade screwdriver, remove both end panels. 2. Using a Phillips head screwdriver, re
Model HMI-103/1052-11. SIDE GLASS REMOVAL 1. Remove front glass assy. per Front Glass Removal Section. 2. Pull side of glass straight up and o
Model HMI-103/1052-13. CONTACTOR 1. Remove electrical power supplied to the unit. To avoid electrical shock or property damage, move power
Model HMI-103/105810 2-92-14. WIRING DIAGRAMS
Model HMI-103/1052-10 8102-14. WIRING DIAGRAMS (Continued)
Model HMI-103/105810 2-112-14. WIRING DIAGRAMS (Continued)
Model HMI-103/1052-12 8102-14. WIRING DIAGRAMS (Continued)
Model HMI-103/105810 2-132-14. WIRING DIAGRAMS (Continued)
Model HMI-103/1052-14 8102-14. WIRING DIAGRAMS (Continued)
Model HMI-103/105810 2-152-14. WIRING DIAGRAMS (Continued)
Model HMI-103/1052-16 207LIMITED WARRANTY FOR HENNY PENNY EQUIPMENTSubject to the following conditions, Henny Penny Corpo
Model HMI-103/105SECTION 3. PARTS INFORMATION3-1. INTRODUCTION This section lists the replaceable parts of the Henny Penny Island Warmer.3-2.
Model HMI-103/1053-2 204Figure 3-1. Control Panel Assy.
Model HMI-103/105 FIG. & ITEM NO. PART NO. DESCRIPTION HMI-103 HMI-105 3-1 CONTROL PANEL ASSY. 1 45710 CONTROL PANEL 1 12 22
Model HMI-103/105Figure 3-2. Terminal Block FIG. & ITEM NO. PART NO. DESCRIPTION HMI-103 HMI-105 1 MS01-382 NYLON RECEPTACLE 2 2
Model HMI-103/105Figure 3-3. Contactor FIG. & ITEM NO. PART NO. DESCRIPTION HMI-103 HMI-105 1 ME50-023 STANDOFF 4 4 2 49547
Model HMI-103/105TABLE OF CONTENTSSection PageSection 1. TROUBLESHOOTING ...
Model HMI-103/105Figure 3-4. Lower Heat3-6 204
Model HMI-103/105707 3-7 FIG. & ITEM NO. PART NO. DESCRIPTION HMI-103 H
Model HMI-103/1053-8 204Figure 3-5. Glass Panels
Model HMI-103/105810 3-9 FIG. & ITEM NO. PART NO. DESCRIPTION HMI-103 HMI-105 3-5 GLASS PANELS (VIEWED FROM CUS
Model HMI-103/105Figure 3-6. Upper Heat FIG. & ITEM NO. PART NO. DESCRIPTION HMI-103 HMI-105 1 45683 CANOPY SHIELD - 1 1 45
Model HMI-103/105
Model HMI-103/105SECTION 1. TROUBLESHOOTING1-1. INTRODUCTION This section provides troubleshooting information in the form of an easy to read
Model HMI-103/1051-3. TROUBLESHOOTING To isolate a malfunction proceed as follows: 1. Clearly defi ne the problem or symptom. 2. Locate the pr
Model HMI-103/105PROBLEM CAUSE CORRECTION• Replace with recommended bulb• Replace socket per Light Socket Section • Check switch and replace if
Model HMI-103/105
Model HMI-103/105SECTION 2. MAINTENANCE2-1. INTRODUCTION This section provides procedures for check out and replacement of the various parts u
Comments to this Manuals