Henny-penny CSM User Manual

Browse online or download User Manual for Food Steamer Henny-penny CSM. Henny Penny CSM User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 11
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
CSL
CSM
CSB
62
INTRODUCTION
This section provides the installation instructions for the Henny Penny Electric Combi-Steamers.
NOTE: The installation of this unit must conform to all local, state, and federal codes. In the absence of codes use
ANSI/NFPA No. 70-latest edition.
NOTE: Canadian installations must conform with the Canadian electrical code, C22.1, Part 1 and/or local codes.
NOTE: The installation of this equipment should be performed by a qualified technician.
LOCATION
The proper location of the unit is very important for operation and convenience. Choose a location which will provide easy
loading and unloading without interfering with the final assembly of food orders.
NOTE: Adequate clearance must be provided for servicing and for operation.
Table Units:
Minimum clearances have to be maintained from the adjacent walls.
Left Side
Right Side Back Side
CSB,CSM,CSL-6, 10, 1020 6” (150mm) 2” (50mm) 2” (50mm)
NOTE: 14” (350mm) is recommended at the left side of the unit for service purposes.
Place the combi-steamer on an original Henny Penny stand or on a level and sturdy surface. Recommended stand height
is 28.5” (725mm).
Minor unevenness of the surface/floor can be compensated by adjusting the legs of the stand or the appliance.
The weight of the units are as follows:
CSB, CSM, CSL-6 297 lbs. (134.5 kg)
CSB, CSM, CSL-10 349 lbs. (158.0 kg)
CSB, CSM, CSL-1020 507lbs. (230.0 kg)
Installation planning should encourage sufficient space to keep the transport trolley/mobile rack at the left-hand side
of the unit.
NOTE: Ventilation must conform to local, state and national codes. Consult your local fire department or building authorities.
X
Do Not puncture the cabinet with any objects such as drills or screws as electrical shock, or component
damage could result.
X
When moving the unit with a pallet jack ensure it is located under the 1-5/8” x 1-5/8” structure frame before
lifting the unit.
Installation – Electric Units
Page view 0
1 2 3 4 5 6 ... 10 11

Summary of Contents

Page 1 - Installation – Electric Units

CSLCSMCSB62INTRODUCTIONThis section provides the installation instructions for the Henny Penny Electric Combi-Steamers.NOTE: The installation of this

Page 2 - (continued)

CSG71GAS SUPPLY (continued)A steam burner gas valve and dry heat burner gas valve respectively are responsible for the gas supply to the indi-vidual b

Page 3 - CHANGES IN VOLTAGE

CSG72NOTE: After turning on the gas, the manual shut-off valve must remain open, except during pressure testing as outlined in theabove steps, or when

Page 4 - DRAIN CONNECTION

CSLCSMCSB63Installation – Electric Units (continued)Floor Units:NOTE: Adequate clearance must be provided for servicing and for operation.Minimum clea

Page 5

CSLCSMCSB64ELECTRICAL SUPPLYStandard electrical supply for all Combi-Steamers is 208-240 volt, 3 phase, 50-60 Hz.NOTE: The power connections are locat

Page 6

CSLCSMCSB65WATER SUPPLYThe Combi-Steamer should only be connected to a cold water supply which meets the quality requirements by theEPA on drinking wa

Page 7 - DRAIN CONNECTION-CSG

CSG66INSTALLATION GAS UNITSThis section provides the installation instructions for the Henny Penny Gas Combi-SteamersNOTE: The installation must confo

Page 8

CSG67Minor unevenness of the surface/floor can be compensated by adjusting the metal legs of the stand or theappliance. The weight of the units are as

Page 9 - CABLE RESTRAINT

CSG68WATER SUPPLY-CSGThe Combi-Steamer should only be connected to a cold water supply which meets the quality requirements by the EPA ondrinking wate

Page 10 - Installation – Gas Units

CSG69Installation – Gas Units (continued)ELECTRICAL SUPPLY-CSGThe gas Combi-Steamer requires 120 volt, single phase, 60 Hertz, 15 amp, 3 wire grounded

Page 11

CSG70GAS SUPPLY-CSGRIGHTMINIMUM PULL of equipment away from wall permissible for accessibility toQuick Disconnect DeviceWRONGAVOID SHARP BENDS AND KIN

Related models: CSB | CSL |

Comments to this Manuals

No comments